Why do I need a fuel management system?
A good fuel management system can interface with an electronic tank gauging system, allowing it to automatically manage level alarms, and send tank level notifications to relevant recipients, such as procurement and suppliers. In this scenario, orders are placed in a timely manner, and emergencies such as tank leaks are addressed swiftly. Any situation where undetected leaks are a possibility should be rectified immediately, as soil decontamination can be extremely costly.
Do you have a good fuel management system?
Consult with your Garaquip Engineer for more information regarding these features.
+263 8677009106/7
+263 (0242) 669682/3, 660655/4
0772 278 262 / 0772 205 254
Email: inquiries@garaquip.co.zw
www.garaquip.co.zw
- Published in Fuel Handling Equipment, Garare Equipment, Oil Handling Equipment
What to Look for When Choosing a Fuel Pump?
- Published in Fuel Handling Equipment
12 Ways to Prevent Gas Theft at Your Station
Higher fuel prices are spurring increased attempts by criminals to steal fuel. Essentially all fraud involving tampering requires access to the equipment, undetected altering of hardware, and knowledge of electronics, no matter what brand of dispenser is involved. Thieves are getting more and more bold, sophisticated and aggressive. Therefore, we are encouraging our customers to develop a security plan to help prevent fraud. No single solution will completely prevent attacks, but careful procedures can significantly reduce the opportunity.
Based on reports from your fellow retailers about incidences across a wide range of pump types and station designs, here are 12 ways to prevent gas theft.
1. Periodically change the programming access (PIN) codes on the manager’s keypad.
This is the most effective method to prevent theft involving dispenser electronics. Trusted station employees and the Authorized Service Contractor (ASC) should be the only personnel with access to these codes. Keep access codes in a secure location known to all station management.
2. For areas subject to high risk of theft, add special keys/locks to replace the standard locks.
This enhancement is extremely effective in preventing access to the dispenser. Custom locks are available in the market and can be installed on existing dispensers and new dispensers by your Authorized Service Contractor.
3. Remove the manager’s keypads from the dispensers and store them in the station or another safe location.
The keypads should be accessible to station management or ASCs should they be needed. A sign-out system can be used to track who last used the keypad. This step can be taken in addition to #1 above.
4. Monitor and compare ‘pump total’ and ‘station total’ reports regularly on the store point of sale and automatic tank gauge.
Station personnel can detect possible theft by noting the difference between ‘pump totals’ and ‘station totals’.
5. Maintain employee views of the fueling islands because thieves don’t like to be seen.
If full view is not possible, due to merchandise displays or other obstructions, utilize video surveillance equipment. Equipment monitoring should be made obvious and signs stating its use should be posted.
6. Be alert to any unit off-line message at the POS.
Should station personnel observe an unexpected offline message, they should know the reason for this. If a customer seems to be fueling at the position offline, this could indicate a theft is in progress if fuel is actually being delivered.
7. Be alert to service calls for dispensers that have been ‘offline’, which may indicate that fraud has occurred.
8. For units left powered during off hours, ensure that power to the Submerged Turbine Pumps (STP) is turned ‘off’.
9. Inspect your site frequently, keeping watch for loose pump faces, doors, stray wires or other parts.
Especially inspect for signs of tampering affecting security features (such as locks, special security kits, calibration seal wires, etc.) that indicate the devices may have been defeated or security compromised.
10. Be alert for abnormal traffic patterns on the forecourt.
Retail fuel suppliers recognize that merchants must protect themselves and their customers from fraud. We will continue to take steps to help merchants increase dispenser resistance to tampering and to provide customer education and recommendations.
11. Check the video security camera tape daily for suspicious activity at the pump.
12. Check the POS settings and change settings on any older POS that allows a “hot-authorization feature.”
Consult with your Garaquip Engineer for more information regarding these features.
T +263 8677009106/7
+263 (0242) 669682/3, 660655/4
0772 278 262 / 0772 205 254
Email: inquiries@garaquip.co.zw
- Published in Fuel Handling Equipment
Setting up a service station in Zimbabwe
Here is the basic procedure that can be followed when establishing a service station.
1. Find and secure a site which has the traffic that will bring about the business volume anticipated.
2. Current / future traffic volume is a key consideration when finding a service station site.
3. Once site is secured > seek licencing approvals from local authority ( RDC for rural sites and Urban Councils for urban sites) NB make sure the site is zoned for service station otherwise change of land purpose maybe necessary.
4. Get a qualified person to design and produce drawings for the service station and all other outbuildings like shop etc. The drawings need to be approved by the local authority where the site is located.
5. After drawings are approved > carry out EMA’s Environmental Impact Assessment (EIA), there are a few consultants who do EIA who are registered with EMA, its important that the consultant is registered.
EMA is the authority that approves the EIA, please note there are fees applicable charged by EMA.
6. Next stage is seek a qualified contractor to construct the service station – this where Garaquip comes in with all the relevant experience and equipment to successfully implement the project.
7. As the investor you may choose to engage an engineering consultant to supervise the construction contractor or you can do it yourself if you got the relevant experience.
8. At all major stages of construction, the local authority building division should be consulted and approvals sort before you go on to next big stage.
9. Once the service station is nearly done , seek an operating licence from ZERA another authority in the energy sector, there are fees to be paid for the licence.
10. Just before start of dispensing fuel the Department of Trade and Measures need to be called in to test and give seal of approval for the fuel dispensing equipment.
- Published in Fuel Handling Equipment